Fort Worth Electrician
You should always consult a professional before doing any electrical work on your own. This electrical service FAQ is meant to be an informational reference, not in-lieu of contacting a professional.
Your home’s safety and compliance aren’t optional. Licensed electricians protect your home from hidden hazards, failed inspections, denied insurance claims, and future resale issues. If a job isn’t done by a licensed pro, you’re gambling with safety and value.
Costs vary based on the complexity of the job — simple repairs are more affordable, major upgrades (like panels or rewiring) require more work. We give free, upfront estimates so you know the price before we start — no surprises, no pressure.
Yes — every homeowner gets a free estimate and inspection. We diagnose the issue, explain it in plain English, and lay out clear options so you call the shots.
A breaker trips because it’s trying to protect your home — usually from overloaded circuits, old panels, or unsafe wiring. Ignoring it only makes the problem worse. We find the real cause — not just reset the breaker.
Sometimes yes. Flickering lights indicate instability in your system — from loose connections to panel issues. We diagnose the root cause and fix it before it becomes a bigger safety risk or costly repair.
If you’re experiencing frequent breaker trips, limited breaker space, or your home can’t keep up with modern electrical demands, the answer is likely yes. A proper panel upgrade boosts safety, capacity, and home value.
Codes change for a reason: safety. Many older homes may work but aren’t up to current standards. We perform thorough safety inspections to identify hidden issues, outdated panels, and grounding problems — before they fail an inspection or cause damage.
The two most common reasons are a tripped GFCI or a tripped breaker. GFCIs are outlets (often found in kitchens, garages, bathrooms, and outdoors) that can be linked together in groups. When one trips, the entire group will turn off. A breaker often trips because the circuit is overloaded (i.e. the group is pulling more power than it can handle). Check out our helpful video on how to reset a GFCI and a breaker.
Circuit breakers trip when there is too much power being used or if there is a problem in the circuit. The devices that use the most power are usually items that use electricity to heat things (e.g. microwave, toaster, space heater, hair dryer, etc.). There are two ways to remedy this issue:
A breaker will also trip if there is a problem in the wiring of the house or the device. Sometimes the devices that use the electricity can have problems internally (like a “short”). Unplug everything on the circuit and see if the circuit breaker stays in the on position. If so, then the problem is with the device. If not, there could be a problem with the outlet or switch itself. If this is the case, call a licensed electrician to troubleshoot the outlet/switch and locate the wiring issue.
To put it simply, breakers can only handle a certain amount of power. If this amount of power is exceeded, it will shut down or “trip”. To know how much power your breaker can handle, look at the number on the breaker inside the panel. This is the amount of amperage it can handle before it trips. Anything that uses electricity to heat or cool uses a lot of power to operate (such as microwaves and toasters) and can often cause breakers to trip when used simultaneously.
For example, if you have a 20 amp breaker and are running both a microwave, which uses 12 amps, and a toaster, which uses 10 amps, you are pulling 22 amps, and therefore will trip your breaker, causing the power to shut off to that area.
You can resolve this issue by not powering devices on the same circuit simultaneously. Or you can have a licensed electrician upgrade your breaker so that you can run more power off of that circuit.
Air conditioners use a lot of power to start up, called a “rush current”. Most AC units have a nameplate or plaque on them that specifically says the maximum or minimum breaker size to operate. If the breaker keeps tripping, make sure the AC and wire are in good operational shape. If they are, installing the maximum allowable breaker for the AC unit should fix the problem.
GFCI (also commonly referred to as GFI) stands for Ground Fault Circuit Interrupter. To put it simply, electricity flows in a circle. There is power on the black wire, which hits the light, and then the white wire (neutral) provides a return path to ground. This completes a circuit and will make the light bulb turn on when power is delivered to it. A GFCI measures the power on the white and black wire. If one wire has an imbalance of .5 milliamps or more, it will shut itself off because that means there is an issue somewhere.
GFCIs trip because of an imbalance in the wiring. GFCIs are required in all areas near water (like bathrooms and kitchens) because they are designed to shut off, for your safety, if water is detected in the outlet. Other reasons a GFI may trip include an old motor or refrigerator, the GFCI itself is bad, or a problem in the circuit wiring.
Yes, this is for your own safety and is a Code requirement. There may be some exceptions made for older homes. For example, a GFI outlet located in the garage of an older home may also protect the bathroom and sometimes the outdoor outlets as well. In a new house, this would be a code violation.
Circuit breakers are sized to the wire that is attached to them. If a smaller-size wire is terminated on a breaker that is too large, the wire can overheat and burn because the breaker will not be providing the protection needed to minimize hazards. There are some exceptions to this rule, with the largest one being a motor such as an AC unit. If you are unsure of the wire size contact a licensed electrician.
The breaker itself is not too difficult to install, however there are several safety considerations and code requirements that need to be followed when connecting a Hot Tub. For example, if metal is present within a 5-foot radius it needs to be bonded (grounded) to the hot tub itself. There are also rules on where the disconnect needs to be. Therefore, it is best to consult with a licensed electrician before installing a new or moving an existing Hot Tub.
Yes, as long as the heat from the LED light is not more than a 60-watt incandescent light bulb, which is unlikely. LED lights use far less energy than a conventional incandescent or halogen light bulb. Check the packaging on your light bulb for information about the wattage.
AFCI stands for Arc Fault Circuit Interrupter. When you are running the vacuum and the plug accidentally pulls out of the wall and you see that spark – that is electricity “arcing”. An AFCI breaker is designed to detect arcing, which could indicate a loose connection. When an AFCI breaker trips, it’s important to determine the cause and whether there may be a hazard present.
We highly recommend having a licensed professional do this for you. Failure to shut off the panel completely or touching dangerous areas of the panel could result in serious injuries or a fire hazard.
Like many electrical projects, changing an outlet/receptacle is not necessarily a difficult task, however there are safety risks (both to you and your home), if not done properly. The most important thing to remember is to turn off power at the breaker or even the whole house before touching any wiring. A licensed electrician can often change out/replace an electrical outlet for you in under an hour, so it is best to call a professional to ensure it is done properly and up to code.
This is usually something that has happened gradually over time. The first sign may have been light “pulsing” when running appliances, like the dryer or AC unit. Losing power in half of the house is usually caused by, what is called, “losing a leg”, meaning one of the two power wires has a bad or loose connection. This can either be caused by the wires coming into your house, which would need to be fixed by the city utilities company. If you suspect this, the utility company will often test and fix this at no charge. It can also be caused by the wiring running from your electrical meter or panel to your house. If this is the case, a licensed electrician can help diagnose and resolve the issue inside your home. Either way, this issue should be addressed quickly, as it could be potentially hazardous.
A light switch removes and connects power to your light. A faint popping noise could simply be an indication of this normal function. The intensity of the noise depends on how much power is on the switch, however there should never be a loud noise coming from a switch. Any loud popping noise(s) should be checked immediately to rule out any hazards.
If the switch is a 3-way switch (able to be operated from 2 places in the home, usually at the top and bottom of the stairs), one switch can be in the up position while the other one is in the down position, which is normal.
Extension cords are not designed to be used for permanent power, but they are safe to use temporarily if they are not damaged and are functioning properly. Be sure to regularly examine your extension cords. If there are nicks, exposed wires, or the end is falling off, it’s time to get a new cord.
Maybe not! Check out our video to determine if you already have tamper-resistant outlets in your home.
Yes. We handle EV charger installations and all major home upgrades — including load calculations, permits, and code‑compliant installations — so your system is safe and functional.
Absolutely. We ensure your panel, wiring, and electrical infrastructure are ready for whatever technology you add — today or tomorrow
Yes — fully licensed, insured, and held to the highest safety and code standards. If it’s our name on the work, it’s done right.
Yes. We stand behind our work with solid warranties. If something isn’t right, we fix it — no exceptions.